Volvo

  • All in one Fluid Stopper Set

    This unique tool allows technicians to stop fluid draining from various lines found on vehicles, heavy duty trucks and equipment.  These clamp style stoppers feature 4 different sizes for various applications including brake lines, hydraulic lines and smaller coolant lines.

    •    4 sizes in one compact clamp 8mm, 10mm, 12mm and banjo
    •    Made from high quality composite plastic
    •    Quick and easy way to stop dripping lines

  • 11600 Extended Length Pneumatic Drift Set

    This unique tool is designed to remove long bolts that have become frozen in place due to rust and time. Examples of these bolts are shock bolts & suspension arm bolts.  These bolts are often too long for conventional pin punches or tapered drifts to push the bolt through a rusty bushing sleeve.
    This tool is operated by attaching to an air hammer and has a 5” long driver section allowing easy removal of rusty bolts and long pins.

    •  Used with common air hammer
    •  3 most common sizes, 5/16”/8mm, 3/8”/10mm & 1/2”12mm
    •  5” long parallel pin driver
    •  3 piece storage bag

  • MAGNETIC WASHER REMOVER

    This specialty designed dual ended tool has small magnets that are designed to aid in the removal of hard to reach washers that are around most types of studs. This tool can also be used to help the technician in the removal of valve adjusting buckets and pucks. Manufactured from light weight and durable glass lled nylon plastic.

  • BENCH HEAD STAND

    Designed for use on most cylinder heads. Holds the head off the bench for valve work, head cleaning and assembly. Holding rods have a long 5″ taper which allows them to go further into the stud hole for more contact in the hole and a rmer grip on the head. Heat treated to remain smooth for use on aluminum heads and comes in a black finish.

  • 89250 MASTER CYLINDER PRESSURE CAP

    Designed with a 1/4″-18″ NPT threaded opening for use with pressure bleeders on most master cylinders or clutch slave cylinders.

  • BELT IT

    BELT IT “SERPENTINE, V-BELT AND TIMING BELT INSTALLATION ASSIST”

    This time saving tool gives the technician the control and reach when installing serpentine
    belts in all applications. The tool was also designed to help install V-belts
    and timing belts that tend to be placed in areas that are dif cult to reach. The three

    pin design gives the technician convenient belt push/pull capability and the handle gives the technician the twisting control to install belts in dif cult areas.

  • UNIVERSAL HOSE PLIERS FITS 1/2in TO 3/4in

    These pliers can be rotated 90° to easily pull the stuck hose from the tting due to corrosion. The specially designed tips of these pliers grip a large surface area and different diameters of the hose to reduce damage during hose removal. The 96600 is made from quality steel and come with soft grip handles.

  • 11070 LARGE CUP SET

    Mobile Hydraulic Press Extended Options: 20 piece kit

    Cup size range:

    Smallest: OD 70mm / ID 62mm

    Largest: OD 88mm / ID 80mm

     

  • 11090 HYDRAULIC PRESS “C” FRAME

    Expand the capabilities of the 11000 series Mobile Hydraulic Press system with the 11090 “C” frame.  The 11090 is used in conjunction with the 11000 or 11000A Mobile Hydraulic Press.  The 11090 allows 300 degree access to bushings and ball joints unlike our conventional twin bolt press frame that allows 180 degrees access.  Designed with “hard to reach” areas in mind, the 11090 can remove and replace hard to get ball joints and bushings where the twin bolt press frame cannot.  The 11090 securly attahes to the hydraulic ram in place of the twin bolt press frame

  • 11080 4 PIECE PULLER ROD SET

    This 4 piece puller rod set is needed to service wheel bearing and the “through hole” bushings.

  • 11100 MANUAL BUSHING R&R SET

    Manual Bushing R&R Tool allows the technician to service a wide range of bushings without removing components from the vehicle. Due to the awkward dimensions of many suspension components using a conventional press to remove and replace bushings can be time consuming and frustrating. This complete system can be used to service the vehicle anywhere in the shop.

  • 13000 STAKED AXLE NUT PUNCHES

    Release and stake the crush type axle nuts found on many vehicles. Used with an air hammer, it is quick and easy to fully disengage the axle nut crimp; reducing damage to the threads.  When re-staking the nut, this tool has the right size and shape to fully lock the nut in place.

  • 13700 ALL IN ONE FLUID STOPPER 2 PIECE SET

    This unique tool allows technicians to stop fluid draining from various lines found on vehicles, heavy duty trucks and equipment.  These clamp style stoppers feature 4 different sizes for various applications including brake lines, hydraulic lines and smaller coolant lines.

  • 14000 BOSCH DIRECT INJECTION INJECTOR PULLER KIT

    This tool has been designed to remove the fuel injectors from GM vehicles produced from 2009 to current with an SIDI engine. Over time and miles the injectors become heavily coated with carbon between the tip and head causing them to stick together. With the engine in this condition the factory tool is too flimsy to remove the injector and will slip off damaging the injector The 14000 will pull the injector straight out without rocking this reduces the possibility of damaging the injector or head.

  • 65350 UNIVERSAL LONG REACH SPARK PLUG BOOT PULLER

    This long reach spark plug boot puller has a swivel action that lets the technician reach down at any angle to grab the spark plug boot and to use leverage to pull the rubber boot from the spark plug without damaging the plug wire. The tips of the tool also have an opening where the spark plug wire can exit the tips.  This tool works on all types of vehicles.